Because the speaker cable carries the largest current in the entire device chain, a suitable conductor cross-section is required to transport it with as little loss as possible. This current generates correspondingly strong magnetic fields and, since it is alternating current, there is a frequency-dependent resistance in the inductance of the cable. Low inductance is therefore particularly important for speaker cables - and this is precisely what has been achieved with the LS-1205 Air: The cable's inductance value has been reduced by a particularly ingenious arrangement of the conductors, the 4-fold "multicore" structure, enabling it to behave in a completely sound-neutral way over a wide frequency range. In addition, the magnetic fields generated around the individual conductors overlap and neutralize each other. This means that all frequencies are transported unhindered and without any time delay, enabling a fabulously open and detailed musical presentation. At the end of the air helix, the LS-1205 Air’s four conductors are separated into so-called aluminum splitters for the receiving connector. In the area between the splitters and plug, in-akustik uses highly flexible molded parts made of a special elastomer. These parts are fixed inside the splitter using a specifically designed plastic plug. This means that the cable remains reliably flexible in the connection area as well. The molded parts run right to the front of the connectors and enclose their inner workings - which underscores the sleek yet attractive design of the LS-1205 Air. Click here and discover the exciting details

The LS-2405 AIR high-end speaker cable offers audiophile enthusiasts a unique sound experience. In the new Referenz LS-2405 AIR loudspeaker cable, we have taken the outstanding properties of its predecessor, the LS-2404 AIR, and developed them even further. The point-to-point Air Helix design now enables the AIR Helix architecture to be used from plug to plug and not just between the sleeves. The 360° BFA bananas and spade lugs are a further innovation, developed in-house for easy and convenient connection to the terminals. These and other technical refinements turn the already exceptional AIR cables into true masterpieces. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology Click here and discover the exciting details

The LS-4005 AIR high-end speaker cable offers audiophile enthusiasts a unique sound experience. In the new Referenz LS-4005 AIR loudspeaker cable, we have taken the outstanding properties of its predecessor, the LS-4004 AIR, and developed them even further. The point-to-point Air Helix design now enables the AIR Helix architecture to be used from plug to plug and not just between the sleeves. The 360° BFA bananas and spade lugs are a further innovation, developed in-house for easy and convenient connection to the terminals. These and other technical refinements turn the already exceptional AIR cables into true masterpieces. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology. Click here and discover the exciting details

High-end loudspeakers need power – and a lot of it, quickly and precisely. For the perfect sound the power must correspond one hundred percent with the analog image of the original sound source, be it an A cappella soloist or a stomping rock concert. A few technical tricks that help to skillfully circumvent physical influences are required to deliver this power to the loudspeaker right on time and holistically. Line resistance and line inductance play an important role with speaker cables. The powerful Referenz LS-8005 AIR has impressive 32 Cross Link Super Speed waveguides with an enormous total cross-section of 38 mm². The cross-section alone, however, does not make a good cable. The smart nesting of the conductors almost completely eliminates magnetic fields, paving the way for the finest sound facets and powerful pressure in equal measure. Good sound needs air! In developing our Air technology, we have proven that an audio cable’s insulation plays a key role and has a significant influence on the sound. This is due to dielectric losses and the electrostatic properties of the insulating materials, which burden the hi-fi system like heavy luggage and make it sluggish. By “omitting” this strain we then help the entire hi-fi chain to achieve top performance. We do this with special clips that guide the signal conductors through the cable in a row and freely suspended. Grounding option: The number of cell phones, WiFi routers, Bluetooth devices, PV systems and charging stations etc., is constantly increasing. This also increases the potential for electromagnetic interferences, which can affect hi-fi and high-end systems. Cables act like antennae and can transfer the interferences to the devices, where they overlay the audio signal in sensitive circuit areas, resulting in a “washed out” sound. Effective shielding and grounding concepts are crucial to protect the sound. The grounding cable of a record player is a very well-known example of this. The LS- 8005 AIR is equipped with a grounding option, which, depending on the configuration, can be connected to the amplifier’s earth, the protective conductor or earth or a grounding box, to divert disturbances. Click here and discover the exciting details

Experts have already been impressed by the LS-1204 AIR (copper). This is how AUDIO summed it up: "A stroke of genius that shows competitors how it should be done – in terms of sound, too. This was wonderfully dynamic, with the most fabulous drive reaching the speaker cones. Admittedly, the price is not low, but the acoustic yield is truly world class. What's more, everything was made by hand. You can feel the love for the product." With the LS-1205 AIR Pure Silver, the currently most filigree model in AIR technology is now also available as a pure silver cable. The structure, dimensions and conductor arrangement of this cable correspond to the copper version of the LS-1205 AIR. As with the LS-4005 AIR Pure Silver and LS-2405 AIR Pure Silver, the conductors have been optimized. Pure silver is used as the conductor material for the LS-1205 AIR Pure Silver too. Under realistic conditions, silver is currently the most conductive material. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. The electrons move 1.5 times faster than in a copper conductor! Click here and discover the exciting details

AIR technology is a milestone in our more than 46-year company history and is causing a sensation in the hi-fi industry worldwide. The approach itself sounds relatively banal: The physically induced losses must be minimized in order to transmit the original music signal as authentically and neutrally as possible. And, thanks to the AIR technology, loss-free transmission is closer than ever before. It leads to a significantly better reproduction, which is not only subjectively audible, but also objectively measurable. The insulation (or dielectric) of the AIR cables is practically perfect thanks to the air insulation, and hardly affects the sound at all. The structure, dimensions and arrangement of the conductors are optimized, and approach the limits of what is physically possible. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology. Click here and discover the exciting details

AIR technology is a milestone in our more than 46-year company history and is causing a sensation in the hi-fi industry worldwide. The approach itself sounds relatively banal: The physically induced losses must be minimized in order to transmit the original music signal as authentically and neutrally as possible. And, thanks to the AIR technology, loss-free transmission is closer than ever before. It leads to a significantly better reproduction, which is not only subjectively audible, but also objectively measurable. The insulation (or dielectric) of the AIR cables is practically perfect thanks to the air insulation, and hardly affects the sound at all. The structure, dimensions and arrangement of the conductors are optimized, and approach the limits of what is physically possible. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. Below you can learn more about the outstanding technical features of this cable, the innovations in the 5th generation and the physical principles used in the AIR technology. Click here and discover the exciting details

High-end loudspeakers need power – and a lot of it, quickly and precisely. For the perfect sound the power must correspond one hundred percent with the analog image of the original sound source, be it an A cappella soloist or a stomping rock concert. A few technical tricks that help to skillfully circumvent physical influences are required to deliver this power to the loudspeaker right on time and holistically. Line resistance and line inductance play an important role with speaker cables. The powerful Referenz LS-8005 AIR has impressive 32 Cross Link Super Speed waveguides with an enormous total cross-section of 38 mm². The cross-section alone, however, does not make a good cable. The smart nesting of the conductors almost completely eliminates magnetic fields, paving the way for the finest sound facets and powerful pressure in equal measure. Good sound needs air! In developing our Air technology, we have proven that an audio cable’s insulation plays a key role and has a significant influence on the sound. This is due to dielectric losses and the electrostatic properties of the insulating materials, which burden the hi-fi system like heavy luggage and make it sluggish. By “omitting” this strain we then help the entire hi-fi chain to achieve top performance. We do this with special clips that guide the signal conductors through the cable in a row and freely suspended. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance, across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper. Grounding option: The number of cell phones, WiFi routers, Bluetooth devices, PV systems and charging stations etc., is constantly increasing. This also increases the potential for electromagnetic interferences, which can affect hi-fi and high-end systems. Cables act like antennae and can transfer the interferences to the devices, where they overlay the audio signal in sensitive circuit areas, resulting in a “washed out” sound. Effective shielding and grounding concepts are crucial to protect the sound. The grounding cable of a record player is a very well-known example of this. The LS- 8005 AIR is equipped with a grounding option, which, depending on the configuration, can be connected to the amplifier’s earth, the protective conductor or earth or a grounding box, to divert disturbances. Click here and discover the exciting details

To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable.

To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.

To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.

To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper.

To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.

To achieve the best possible sound, it is crucial that the amplifier has a firm grip on the speakers. In addition to activating the membranes to make them vibrate, it must also be able to dampen them effectively. One measure of this is the amplifier’s damping factor. The speakers’ actual damping factor is significantly influenced by the quality of the speaker cables and connecting bridges of the bi-wiring terminals. The original bridges often consist of simple stamped sheet metal parts of inferior quality. The new in-akustik AIR High End Bi-Wire Jumpers are based on the technologies, findings and materials of the renowned LS-1205 AIR, LS-2405 AIR and LS-4005 AIR speaker cables. If bi-wiring is not an option, these high-end bi-wire jumpers offer an excellent alternative to the often inferior metal bridges on the speaker terminals. They ensure an even and controlled signal distribution, which is perfectly harmonized with the respective speaker cable. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper. BFA & Spade 360° (LS-4005 AIR & LS-2405 AIR): Movement across three axes make the 360-degree BFA and spade connectors really easy to connect and disconnect. Difficult set-up operations that put a strain on both cables and devices are a thing of the past. The connectors can easily be attached to terminals from a wide range of manufacturers. No awkward bending is necessary, avoiding damage to surfaces and potential contact resistance. Set-up is fast and problem-free. The attractively designed connectors are the perfect complement to the outstanding sound. The new connectors are used with the LS-4005 and the LS-2405. Both connector versions as well as the Basic version for the LS-1205 are pressure-grouted with a force of 1.5 tonnes.

Cable capacitance plays a decisive role, especially for audio cable connections between individual devices. As the signal sources are very weak and react sensitively to high cable capacitance, audio cables are virtually predestined for air insulation using air helix technology. In addition to this, we have also developed a completely new and entirely solder-free RCA connector for the Referenz NF-1205 Air. It consists of several component parts that are only joined together during the course of the assembly process. As with the loudspeaker cable, the thin layer of enamel is first removed from the high-purity copper wires of the "Cross Link Super Speed" waveguide by machine. Then, the contact pin of the connector, which is made of tellurium copper, is pressure-grouted with the conductor using a force of 1.5 tonnes. The connection of the shielding is also completely new: It is now hermetically sealed with screws. Click here and discover the exciting details

Cable capacitance plays a decisive role, especially for audio cable connections between individual devices. As the signal sources are very weak and react sensitively to high cable capacitance, audio cables are virtually predestined for air insulation using air helix technology. New XLR 180° plug: It is only possible to insert XLR connectors in one direction. This can be annoying as the position of the XLR sockets in devices varies. In order for the cable to fit, it must sometimes be twisted by force. This puts a strain on cables, plugs and device sockets and sometimes simply looks a mess. The newly developed XLR 180° plugs can each be rotated by +/- 45 degrees, i.e. +/- 90 degrees in total. The finishing touch for perfect cabling. Click here and discover the exciting details

Breathtaking sound thanks to air insulation - we have already created many innovative designs on the way to perfect insulation, such as DUO-PE insulation or PETS (PE Tube Support). The Referenz NF-2405 cable is another true milestone and an absolute world first in the cable sector. Normally, the conductors are kept at a distance from each other by more or less high-quality filling and insulation materials. With the NF-2405, however, the conductors run through a series of clips connected in series, which form the inner framework and give the NF-2405 exceptional flexibility for high-end cables. The NF-2405 is manufactured entirely in Germany, like all speaker and audio cables in the Referenz series. The clips are assembled by hand with meticulous care in the company's own factory and then the Cross Link super-speed waveguide is threaded in. After this, the resulting air helix is also shielded by hand and given a PE network jacket before the finished cable is assembled using the RCA plugs we developed ourselves. New RCA SL connector: Soldering is a reliable and well-established joining technique, but it has its drawbacks. Disadvantages include the presence of poorly conducting solder in the signal path and the emergence of low thermoelectric emfs. With the SL RCA Plug developed in-house, the connections from the signal conductor to the contact elements are precisely pressure-grouted together using a force of 1.5 tonnes. A further seemingly tiny improvement that brings great rewards in terms of audio performance. Click here and discover the exciting details

Breathtaking sound thanks to air insulation - we have already created many innovative designs on the way to perfect insulation, such as DUO-PE insulation or PETS (PE Tube Support). The Referenz NF-2405 cable is another true milestone and an absolute world first in the cable sector. Normally, the conductors are kept at a distance from each other by more or less high-quality filling and insulation materials. With the NF-2405, however, the conductors run through a series of clips connected in series, which form the inner framework and give the NF-2405 exceptional flexibility for high-end cables. The NF-2405 is manufactured entirely in Germany, like all speaker and audio cables in the Referenz series. The clips are assembled by hand with meticulous care in the company's own factory and then the Cross Link super-speed waveguide is threaded in. The resulting Air Helix is then also shielded by hand and fitted with a PE network jacket before the finished cable is assembled with the XLR 180° connectors developed in-house. New XLR 180° plug: It is only possible to insert XLR connectors in one direction. This can be annoying as the position of the XLR sockets in devices varies. In order for the cable to fit, it must sometimes be twisted by force. This puts a strain on cables, plugs and device sockets and sometimes simply looks a mess. The new XLR 180° plugs developed in-house can be rotated by +/- 45 degrees, i.e., up to a total of +/- 90 degrees from connector to connector. The finishing touch for perfect cabling. Click here and discover the exciting details

Good sound needs space! In developing our Air technology, we have proven that an audio cable’s insulation plays a decisive role and has a significant influence on the sound. This is due to dielectric losses and the electrostatic properties of the insulating materials, which burden the hi-fi system like heavy luggage and make it sluggish. By “omitting” this strain we then help the entire hi-fi chain to achieve top performance. We do this with special clips that guide the signal conductors through the cable in a row and freely suspended. A cable’s geometry also influences these factors. Bigger distances mean less load. This is exactly where our NF-4005 AIR comes in: The AIR helix design and the cable’s dimensions create even more space and air between the signal conductors. The cable thus forms a wide audiophile corridor and rolls out the red carpet, so to speak, for every sound detail. New RCA SL connectors (SolderLess): Soldering is a proven and established connection technology, but it is not without its weaknesses. These include the solder used in the signal path, which reduces the conductivity, and the generation of thermal voltages, even if it is kept to a minimum. With our recently developed SL (SolderLess) RCA connector, the connections from the signal conductor to the contact element are pressed with the highest precision and with a pressure of 1.5 tonnes. A further seemingly tiny improvement that brings great rewards in terms of audio performance. Click here and discover the exciting details

Good sound needs space! In developing our Air technology, we have proven that an audio cable’s insulation plays a decisive role and has a significant influence on the sound. This is due to dielectric losses and the electrostatic properties of the insulating materials, which burden the hi-fi system like heavy luggage and make it sluggish. By “omitting” this strain we then help the entire hi-fi chain to achieve top performance. We do this with special clips that guide the signal conductors through the cable in a row and freely suspended. A cable’s geometry also influences these factors. Bigger distances mean less load. This is exactly where our NF-4005 AIR comes in: The AIR helix design and the cable’s dimensions create even more space and air between the signal conductors. The cable thus forms a wide audiophile corridor and rolls out the red carpet, so to speak, for every sound detail. New XLR 180° plug: It is only possible to insert XLR connectors in one direction. This can be annoying as the position of the XLR sockets in devices varies. In order for the cable to fit, it must sometimes be twisted by force. This puts a strain on cables, plugs and device sockets and sometimes simply looks a mess. The new XLR 180° plugs developed in-house can be rotated by +/- 45 degrees, i.e., up to a total of +/- 90 degrees from connector to connector. The finishing touch for perfect cabling. Click here and discover the exciting details

Good sound needs space! In developing our Air technology, we have proven that an audio cable’s insulation plays a decisive role and has a significant influence on the sound. This is due to dielectric losses and the electrostatic properties of the insulating materials, which burden the hi-fi system like heavy luggage and make it sluggish. By “omitting” this strain we then help the entire hi-fi chain to achieve top performance. We do this with special clips that guide the signal conductors through the cable in a row and freely suspended. A cable’s geometry also influences these factors. Bigger distances mean less load. This is exactly where our NF-4005 AIR Pure Silver comes in: The AIR helix design and the cable’s dimensions create even more space and air between the signal conductors. The cable thus forms a wide audiophile corridor and rolls out the red carpet, so to speak, for every sound detail. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance, across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper. New RCA SL connectors (SolderLess): Soldering is a proven and established connection technology, but it is not without its weaknesses. These include the solder used in the signal path, which reduces the conductivity, and the generation of thermal voltages, even if it is kept to a minimum. With our recently developed SL (SolderLess) RCA connector, the connections from the signal conductor to the contact element are pressed with the highest precision and with a pressure of 1.5 tonnes. A further seemingly tiny improvement that brings great rewards in terms of audio performance. Click here and discover the exciting details

Good sound needs space! In developing our Air technology, we have proven that an audio cable’s insulation plays a decisive role and has a significant influence on the sound. This is due to dielectric losses and the electrostatic properties of the insulating materials, which burden the hi-fi system like heavy luggage and make it sluggish. By “omitting” this strain we then help the entire hi-fi chain to achieve top performance. We do this with special clips that guide the signal conductors through the cable in a row and freely suspended. A cable’s geometry also influences these factors. Bigger distances mean less load. This is exactly where our NF-4005 AIR Pure Silver comes in: The AIR helix design and the cable’s dimensions create even more space and air between the signal conductors. The cable thus forms a wide audiophile corridor and rolls out the red carpet, so to speak, for every sound detail. To get closer to the pinnacle of audiophile perfection, we also carefully examined the conductor material. Copper in the right purity is itself already an excellent conductor, but a superconductor with no ohmic resistance to the current would be simply perfect. The material’s superconducting properties, however, require extremely low temperatures of at least -70 degrees. Under realistic conditions, silver is currently the most conductive material. With a conductivity of 61.35 S/m (siemens per meter), it outperforms copper by around six percent. Many manufacturers only use silver-plated conductors, which over time can seem, “bright”, “metallic” and even, “annoying”. We, on the other hand, use pure silver, which has a far more neutral sound. Due to the higher drift speed of the electrons, our pure silver cable delivers a more penetrating and sumptuous sound performance, across all frequency ranges. On the other hand of course, silver is about one hundred times more expensive than copper. New XLR 180° plug: It is only possible to insert XLR connectors in one direction. This can be annoying as the position of the XLR sockets in devices varies. In order for the cable to fit, it must sometimes be twisted by force. This puts a strain on cables, plugs and device sockets and sometimes simply looks a mess. The new XLR 180° plugs developed in-house can be rotated by +/- 45 degrees, i.e., up to a total of +/- 90 degrees from connector to connector. The finishing touch for perfect cabling. Click here and discover the exciting details

Cable capacitance plays a decisive role, especially for audio cable connections between individual devices. As the signal sources are very weak and react sensitively to high cable capacitance, audio cables are virtually predestined for air insulation using air helix technology. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. New XLR 180° plug: It is only possible to insert XLR connectors in one direction. This can be annoying as the position of the XLR sockets in devices varies. In order for the cable to fit, it must sometimes be twisted by force. This puts a strain on cables, plugs and device sockets and sometimes simply looks a mess. The newly developed XLR 180° plugs can each be rotated by +/- 45 degrees, i.e. +/- 90 degrees in total. The finishing touch for perfect cabling. Click here and discover the exciting details

Our AIR cables have already caused something of a sensation in the world of high-end connections: “The best cable ever connected here between amp and speakers!” (AUDIO 02-2020| LS-2404 AIR PURE SILVER). With the NF-2405 AIR Pure Silver, the analog member of the AIR family is now also available as a pure silver cable. AIR technology is a milestone in our more than 46-year company history and is causing a sensation in the hi-fi industry worldwide. The approach itself sounds relatively banal: The physically induced losses must be minimized in order to transmit the original music signal as authentically and neutrally as possible. And, thanks to the AIR technology, loss-free transmission is closer than ever before. It leads to significantly better sound reproduction, which is not only subjectively audible but also objectively measurable. The insulation (or dielectric) of the AIR cables is practically perfect thanks to the air insulation, and hardly affects the sound at all. The structure, dimensions and arrangement of the conductors are optimized, and approach the limits of what is physically possible. Adding another highlight to this perfect audiophile foundation, we then focused on the conductor material of the cables. Copper in the appropriate purity is already a very good conductor. A superconductor, where electrical resistance is zero, would be perfect, of course. Unfortunately, superconducting materials require temperatures of at least -70 degrees. Under realistic operating conditions, the best conducting material we have is currently silver. At 61.35 S/m (Siemens pro Meter), its conductivity is approximately six percent superior to that of copper. However, this precious metal is about 100 times more expensive. New RCA SL connector: Soldering is a reliable and well-established joining technique, but it has its drawbacks. Disadvantages include the presence of poorly conducting solder in the signal path and the emergence of low thermoelectric emfs. With the SL RCA Plug developed in-house, the connections from the signal conductor to the contact elements are precisely pressure-grouted together using a force of 1.5 tonnes. A further seemingly tiny improvement that brings great rewards in terms of audio performance. Click here and discover the exciting details